Starter Replacement ?
If you try to start your vehicle and the engine turns too slowly, or not at all, the starter or solenoid may need to be replaced. Before replacement, make sure that the starter or solenoid is the problem. Have both checked if you have any doubts. Also check your battery and battery/starter cables for any wear and corrosion. Clean up the corrosion and replace the battery or cables if needed. If your vehicle has a starter-mounted solenoid, it’s a good idea to replace the solenoid when you replace the starter.
Tools and equipment
To replace your starter you will need:
- Sockets and wrenches
- Screwdriver Pliers
- Battery terminal puller
- Drive-on ramps, jack or jack stands
BEFORE YOU BEGIN
Proper maintenance and service procedures are vital to the safe, efficient operation of all motor vehicles, as well as to the safety of the person performing the work—you.
Whenever you’re working on your vehicle, we recommend that you follow these important safety rules:
- Do have a first-aid kit handy. Do be careful when working around hot or sharp objects.
- Do follow the manufacturer’s instructions for all products.
- Do use safety stands under the frame or drive-on-ramps if you must raise your vehicle.
- Don’t run the engine without proper ventilation.
- Don’t smoke when working around the engine.
READ these instructions completely before you begin:
- Get the correct starter and solenoid for your vehicle. Check with your local NAPA Auto Parts store for the specific parts you need.
- Let the engine cool.
- Gather together all the necessary tools.
- Place the vehicle on ramps, or jack up the front and support it on jack stands. Follow all safety precautions. BLOCK the rear wheels. NEVER work under a vehicle supported by a jack.
- Be sure the ignition is OFF and then remove the negative (grounded) battery cable from the battery with the puller after loosening the attaching bolt.
- Note all wiring connections to the starter and solenoid. Figure 1 is a generic diagram of a starter system.
Replacing the Starter
- Remove the battery/starter cable attached to the starter-mounted solenoid or to the starter.
Remove any other wires attached to the solenoid if it is starter-mounted. Note the wire positions so you can replace them correctly.
- Remove the starter motor attaching bolts (usually two or three). Most bolts attach horizontally through the mounting flange. On GM cars, the bolts are vertical (see Figure 2), and there may be a shim between the engine and starter block. If there is one, it must be used with the new starter. Remove any support bracket that holds the front of the starter.
- Drop the starter down. You may have to turn the wheels to one side or disconnect an idler arm on some Ford cars. On other cars you may have to remove or loosen transmission oil cooler lines or brackets, the exhaust pipe, flywheel housing cover, cross member, ground strap, oil pressure sending unit or other parts to give you enough clearance to drop the starter down.
- Install the new starter in the reverse order of removal. Be sure you replace the original shim(s) on the GM-type starter if there were any when you removed the old starter. If there is a noise when the engine is starting or a whine after it starts, you may need to adjust the shims as follows:
- If there is a starter motor noise when you crank the engine, remove one full-length shim or add one short shim to the outboard pad only.
- If there is a high-pitched whine after the engine fires, add full-length shims one at a time until the noise disappears. DO NOT use more than four shims. To add a full-length shim, loosen bolt A, remove bolt B, add the shim and then re-tighten both bolts (see Figure 3).
- Reattach the battery/starter cable to the starter. If the starter solenoid is mounted, reconnect any other wires to it in their original positions.
Replacing the Solenoid
Solenoids are located either on a panel in the engine compartment or on the starter itself.
- To replace a panel-mounted solenoid:
- Remove the cable from the battery, the cable to the starter, and the small wire or wires, being sure to note their exact locations.
- Remove the mounting screws and lift off the solenoid.
- Install the new solenoid in the same location and reattach the wires and cable to the same terminals. Tighten all connections.
- To replace a starter-mounted solenoid:
- Remove the starter.
- Remove the field coil strap from the solenoid terminal.
- Remove the attaching screws and bolts and remove the solenoid housing. You may have to rotate the housing. On some starters, the plunger and spring may be loose. On others, the solenoid plunger stays in the solenoid, and the end will have to be worked off the starter shift lever.
- Install the new solenoid in the reverse order of removal. If the plunger stays with the solenoid, the end must be engaged with the starter shift lever. If the solenoid plunger remained attached to the starter, insert it in the solenoid. Make sure the spring is in place between the plunger and solenoid body. Hold the body in place and tighten the attaching screws.
- Reconnect the cable and wiring when you install the starter.
- Reconnect the ground cable to the battery.
- Follow these instructions carefully. Read and be sure you understand them before you begin.
- Gather all your tools and supplies before you begin.
- Allow plenty of time to do the job so you don’t have to hurry.
- Remember that these are general instructions. For more detailed instructions pertaining to your specific vehicle, consult an appropriate repair manual.
- Safety is important whenever you’re working around machinery. Beware of hot objects, sharp instruments and hazardous materials.
- Don’t substitute tools unless you’re sure you won’t compromise either your safety or the performance of your vehicle.
- If you have any questions about repair and maintenance, contact your local Auto Parts store, or come and visit us: at Mac’s Auto Electric, your local Starter motor supplier.
- 496 Bay St, Victoria, BC.